The CLW-DIM4RF is a 1000 Watt wall mount dimmer and programmable keypad designed to operate as part of a complete Crestron automation system communicating via the infiNET wireless control network. Without the need for additional control wiring, the CLW-DIM4RF easily replaces any standard in-wall dimmer or light switch*. Although functional as a standalone dimmer, the CLW-DIM4RF delivers greatly enhanced automation and control capability when Connected to Crestron's PAC2 or PAC2M automation control system (or any other 2-Series control system) via the infiNET network.
infiNET™
Crestron's groundbreaking infiNET wireless technology affords reliable 2-way communications throughout a home or office structure without the need for physical control wiring. Numerous infiNET dimmers, switches, and other devices can be linked to the control system via a single RF gateway. Employing a 2.4 GHz mesh network topology, every infiNET device functions as an RF repeater, increasing effective range and reinforcing the complete network by providing multiple redundant signal paths within the mesh network.
Lighting and Keypad Control
By default, the CLW-DIM4RF's top left pushbutton provides easy dimming control with access to 3 user presets. Tapping this button toggles the dimmer between preset 1 and full off. Presets 2 and 3 are selected by double-tapping the same button. With each selection, the lighting levels fade naturally between each preset level. Pressing and holding the button allows for manual adjustment of the lighting level.
All four pushbuttons are software programmable for any Crestron system function, enabling control over additional lighting circuits, fans, drapes, audio levels, etc. right from a single CLW-DIM4RF.
A slide switch is also provided to select between RUN, SET, and OFF modes. RUN is the normal operating mode as described above. SET mode is used for storing presets, while switching to the OFF mode completely disables the dimmer and disconnects all power to the load to facilitate changing bulbs.
The status LED serves a dual purpose, providing helpful status confirmation during operation and setup, and glowing dimly when idle to make the dimmer easy to locate in the dark.
Automation System Integration
Connecting the CLW-DIM4RF to a control system enables its keypad functionality as described above, and also allows its local dimming functions to be controlled from other keypads, touch panels, wireless remotes, and computers to support unlimited Flexibility for remote control and integration with other devices and systems. In the event that communication with the control system is disrupted for any reason, the CLW-DIM4RF will remain operable to control the local lighting circuit.
Easy Installation
System design, installation, and upgrade using infiNET dimmers could not be easier. Since there's no control wire required, the CLW-DIM4RF can be installed just like any conventional dimmer*. Multiple units may be ganged side-by-side along with other dimmers, switches and non-Crestron devices. (Note: Ganging the CLW-DIM4RF typically requires the removal of the side heat sink fin on one or both sides of the unit resulting in a derating of its load capacity; see specifications below.)
Setting up a complete network of infiNET devices is simple, utilizing dynamic discovery (self-install) to locate and acquire each RF device automatically. Setting the RF ID of each device employs the same convention as Crestron's familiar TSID method, and each device is programmable using CrestronSIMPL™Windows , SystemBuilder™ orD3Pro™ software just like any wired Cresnet device. Even firmware updates are performed over the wireless network.
No further action is required to configure the infiNET network. Each device assigned to a common gateway automatically behaves as a repeater for any other devices within range (approximately 150 feet indoors), and additional repeaters may be added if necessary. At all times, the infiNET gateway monitors each device on the network, ignoring any other 2.4 GHz signals, and reconfiguring the entire network automatically in response to new sources of interference and other changes in RF conditions.
Color Options
infiNET Dimmers and Switches are available in white, black, or almond, with or without custom button engraving. Complete installation requires a decorator style faceplate (not included).
Note: For multipoint dimming, use CLW-DIMS4RF