Crestron

Horizon™ paintable trim (HZ-TRIM-G series) provides a set of top and bottom trim pieces for use with a Horizon keypad (HZ-KPCN series). Each plastic trim piece is lightly textured to accept the application of a custom paint finish. They are available in either dark gray or light gray to accommodate a full spectrum of paint colors.The paintable trim pieces install in place of the standard trim that ships with each keypad and faceplate (HZ-FP-G series). They attach magnetically, allowing for an...

The custom-engraved LCDB3-BTN button caps afford personalization for the C2N-LCDB3’s three backlit pushbuttons. The button caps are available in gray with a texturized finish. Buttons can be ordered by using the Crestron Engraver software.

The custom-engraved LCDB3-BTN button caps afford personalization for the C2N-LCDB3’s three backlit pushbuttons. The button caps are available in gray with a texturized finish. Buttons can be ordered by using the Crestron Engraver software.

Provides a set of ten blank button labels without engraving for an MPC3-302-B or MPC3-302-W 3-Series® Media Presentation Controller.Note: The blank labels may be custom laser engraved by a third party. To obtain the labels from Crestron with custom laser-etched engraving, see models MPB3/MPC3-BTN10-B ENGRAVED and MPB3/MPC3-BTN10-W ENGRAVED.

Provides a set of ten button labels with custom laser-etched engraving for an MPC3-302-Bor MPC3-302-W 3-Series® Media Presentation Controller. Specifying engraving is easy using Crestron Engraver software.Note: To obtain a set of ten blank labels without engraving, see models MPB3/MPC3-BTN10-B BLANK and MPB3/MPC3-BTN10-W BLANK.

Provides a set of ten blank button labels without engraving for an MPC3-302-B or MPC3-302-W 3-Series® Media Presentation Controller.Note: The blank labels may be custom laser engraved by a third party. To obtain the labels from Crestron with custom laser-etched engraving, see models MPB3/MPC3-BTN10-B ENGRAVED and MPB3/MPC3-BTN10-W ENGRAVED.

Provides a set of ten button labels with custom laser-etched engraving for an MPC3-302-B or MPC3-302-W 3-Series® Media Presentation Controller. Specifying engraving is easy using Crestron Engraver software.Note: To obtain a set of ten blank labels without engraving, see models MPB3/MPC3-BTN10-B BLANK and MPB3/MPC3-BTN10-W BLANK.

Provides a set of three blank icon chips without engraving for an MPC3-201-B 3-Series® Media Presentation Controller.Note: The blank icon chips may be custom laser engraved by a third party. To obtain the icon chips from Crestron with custom laser-etched engraving, see model MPB3/MPC3-BTN3-B ENGRAVED.

Provides a set of three icon chips with custom laser-etched engraving for an MPC3-201-B3-Series® Media Presentation Controller. Specifying engraving is easy using Crestron Engraver software.Note: To obtain a set of three blank icon chips without engraving, see model MPB3/MPC3-BTN3-B BLANK.

The MPC3/MPB3-TTK-SQR-B Tabletop Kit provides a stylish tabletop enclosure for the MPC3-201-B 3-Series® Media Presentation Controller. When installed in the enclosure, the controller’s front panel sits flush with the enclosure housing, tilted at a 45° angle. A 3.6 m (12 ft) CAT5e LAN cable is included. The cable is black in color, and passes out the rear of the enclosure through a strain-relieving grommet. The complete assembly may be placed on any flat, level surface for use. Key...