Crestron HD-DA8-4KZ-E

Splits one HDMI® source to eight separate outputs. Supports 4K60 4:4:4 and HDR video signals with high-bitrate 7.1 audio.



The Crestron® HD-DA8-4KZ-E is a simple to use, high-performance 4K AV distribution amplifier designed to split a single HDMI® signal to feed up to eight separate displays, switchers, and/or other devices. It provides full support for UHD and DCI 4K60 4:4:4 and HDR video, HDCP 1.4 or 2.2 copy protection, and high-bitrate 7.1 audio, to ensure optimal performance and compatibility for any HD or 4K video application. No programming or control system is required for operation.

Video
Input Signal Type	HDMI w/HDR10, Deep Color, 3D, & 4K60 4:4:4 support[1] (DVI & Dual-Mode DisplayPort compatible[2])
Output Signal Type	HDMI w/HDR10, Deep Color, 3D, & 4K60 4:4:4 support[1] (DVI compatible[2])
Copy Protection	Selectable for HDCP 2.2, HDCP 1.4, or HDCP disabled
Maximum Resolutions Scan Type Resolution Frame Rate Color Sampling Color Depth Progressive 4096x2160 DCI 4K or 3840x2160 4K UHD 24 Hz 4:4:4 36 bit 30 Hz 4:4:4 36 bit 60 Hz 4:2:2 36 bit 60 Hz 4:4:4 24 bit 2560x1600 WQXGA 60 Hz 4:4:4 36 bit 1920x1080 HD 1080p 60 Hz 4:4:4 36 bit Interlaced 1920x1080 HD 1080i 30 Hz 4:4:4 36 bit NOTE: Common resolutions are shown; other resolutions are supported at pixel clock rates up to 600 MHz
Audio
Input Signal Type	HDMI (Dual-Mode DisplayPort compatible[2])
Output Signal Type	HDMI
Formats	Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS®, DTS-ES, DTS 96/24, DTS HD High Res, DTS HD Master Audio, DTS:X, LPCM up to 8 channels
Communications
USB	USB 2.0 host; supports firmware update and custom EDID upload via a USB flash drive
HDMI	HDCP & EDID (does not pass CEC)
HDCP Version	Selectable for HDCP 2.2, 1.4, or OFF; HDCP encrypted content is blanked in OFF mode
EDID Mode	Selectable for DEFAULT or COPY 1ST; • The factory default EDID is 4K60 4:4:4 non-HDR video with 2-channel LPCM audio; • The factory default EDID can be replaced with a custom EDID via USB; • Sliding the switch from DEFAULT to COPY 1ST copies and stores the EDID from the device at OUTPUT 1 and passes it to the INPUT source device; • Sliding the switch from COPY 1ST to DEFAULT erases the stored EDID and uses the factory default or custom EDID; Note: Changing the device at OUTPUT 1 will not update the stored EDID until the switch is moved to DEFAULT and back to COPY 1ST
Connectors
INPUT	(1) HDMI Type A connector, female; HDMI digital video/audio input[1]; (DVI & Dual-Mode DisplayPort compatible[2])
OUTPUT 1 – 8	(8) HDMI Type A connectors, female; HDMI digital video/audio outputs[1]; (DVI compatible[2])
SERVICE	(1) USB Type A connector, female; USB 2.0 host port; For firmware update and custom EDID upload via a USB flash drive
24VDC 0.75A	(1) 2.1 x 5.5 mm DC power connector; 24 Volt DC power input; PW-2407WU power pack included
Controls & Indicators
PWR	(1) Bi-color LED, indicates operating power is supplied via the power pack; illuminates amber while booting, green when operating
SETUP	(1) Pushbutton and (1) red LED, restores factory settings
RESET	(1) Recessed pushbutton for hardware reset
INPUT	(1) Green LED, indicates video signal presence at the HDMI input
OUTPUT 1 – 8	(8) Green LEDs, each indicates video signal transmission at the corresponding HDMI output
HDCP	(1) 3-position slide switch, selects the HDCP version (OFF, 1.4, or 2.2)
EDID	(1) 2-position slide switch, selects the EDID mode (DEFAUT or COPY 1ST)
Power
Power Pack (included)	Input: 100-240 Volts AC, 50/60 Hz; Output: 0.75 Amps @ 24 Volts DC; Model: PW-2407WU
Environmental
Temperature	32° to 104° F (0° to 40° C)
Humidity	10% to 90% RH (non-condensing)
Enclosure
Chassis	Metal, black finish, with (2) integral mounting flanges
Mounting	Freestanding, surface mount, or attach to a single rack rail
Dimensions
Height	0.87 in (22 mm)
Width	12.82 in (326 mm)
Depth	4.67 in (119 mm)
Compliance
CE, IC, FCC part 15 Class B digital device