Crestron HD-MD-200-C-E

Provides a simple and cost-effective high-definition AV presentation solution for classrooms and meeting spaces. It is composed of a DM Lite surface mount transmitter (HD-TX-101-C-E) and receiver (HD-RX-201-C-E), which connect together over a single CATx cable at up to 230 ft (70 m). Provides a single HDMI® input at the transmitter, and an additional HDMI input at the receiver. Built-in scaling ensures a reliable, high-quality video image. Fully-automatic operation and web browser setup eliminate the need for a control panel, control system, or programming.

The Crestron® HD-MD-200-C-E delivers an incredibly simple and cost-effective multimedia presentation solution for classrooms and meeting spaces. It allows a laptop or mobile device to be connected to an HDMI® input at a table or podium, and routes the signal to a display or projector up to 230 feet (70 meters) away. An additional HDMI source can be connected at the display device location (or through an optional wall plate near the display). Fully automatic operation detects when a source is connected or disconnected at either input and turns the display on and off, alleviating the need for any control panels or remotes. Built-in scaling ensures an optimal video image for SD and HD video signals, as well as for high-res computer signals.

Composed of a compact transmitter and receiver pair (models HD-TX-101-C-E and HD-RX-201-C-E respectively), the HD-MD-200-C-E installs in minutes and requires no special programming. The transmitter mounts beneath the table or inside the podium, while the receiver mounts behind the display or above the projector. The only connection required between the transmitter and receiver is a single CAT type twisted pair cable.[1] A LAN port on the receiver allows for connection to an Ethernet network to enable easy setup and configuration via a web browser. Advanced functionality is enabled through integration with a Crestron control system.

Computer/AV Auto-Switcher
The HD-MD-200-C-E handles high-definition video and computer sources with resolutions up to Full HD 1080p60, 1080i30, or WUXGA 1920x1200. A single HDMI input is provided on the transmitter to support the connection of a computer, mobile device, or other media source. An additional HDMI input is provided on the receiver, which may be wired to an optional wall plate or used to connect a local source such as a mini PC or Crestron AirMedia® wireless presentation system.

The inputs on both components can be configured to switch automatically or be controlled through a Crestron control system. Auto-detection on each input enables plug-and-play simplicity, supporting HDMI, DVI, or Dual-Mode DisplayPort signals via either HDMI input.[2] The auto-switching behavior can be configured using “priority routing” mode, allowing the installer to define which input takes precedence over the other when connecting multiple sources.

A single HDMI output is provided on the receiver to feed the display device. This output can support either HDMI or DVI signal types.[3] A stereo analog audio output is also included to feed an optional sound bar or amplifier.[4]

Multihead Cable Option
A USB power port is included on the HD-TX-101-C-E transmitter to enable use of a Crestron Multihead HD Video Cable (model CBL-MULTI-HD-6, sold separately). The Multihead cable provides expanded input connectivity to support the connection of a laptop computer or mobile device with HDMI, DisplayPort, Mini DisplayPort, or USB Type-C™ video output.[5]

HD Signal Extender
A single CAT type cable (sold separately) links the HD-MD-200-C-E transmitter and receiver together. This cable can be up to 230 feet (70 meters) in length, offering an ideal point-to-point signal extender solution for virtually any room with a single table or podium and one display device.[1]

HD Scaler
One might assume that any modern display device should support whatever sources you connect to it. In fact, many displays just can’t handle all the different formats and resolutions you’re likely to encounter day-to-day in a dynamic presentation environment. With its built-in professional scaler, the HD-MD-200-C-E enables support for a complete range of digital and analog signals, ensuring that every source displays reliably and beautifully. Automatic calibration is achieved using the display’s EDID [6] — just connect the receiver to the display and it intelligently converts and enhances the signal for optimal appearance on the display screen.

EDID Format Management
To ensure that every source gets displayed at its optimal resolution and format, the HD-MD-200-C-E provides comprehensive management of the EDID information that passes between the display, scaler, and source devices. Most applications require no changes to the default settings. For applications requiring custom configuration, the HD-MD-200-C-E allows for easy assessment of each device’s format and resolution capabilities, with the ability to configure signals appropriately for the most desirable and predictable behavior.

QuickSwitch HD™ Technology
Handling digital media signals means handling HDCP (High-bandwidth Digital Content Protection), the encryption scheme used by content providers to protect their DVDs, Blu-ray™ discs, and broadcast signals against unauthorized copying. Viewing HDCP encrypted content requires a source device to “authenticate” each display and signal processor in the system and issue it a “key” before delivering an output signal. Crestron QuickSwitch HD manages these keys to ensure fast, reliable switching and immunity to “blackouts.”

Audio De-Embedding
Its analog audio output allows the HD-MD-200-C-E to extract the stereo audio signal from digital sources to feed a sound bar, amplified speakers, or a separate sound system.[4]

Embedded Device Control
To deliver fully automatic operation of the complete system, the HD-MD-200-C-E can turn the display device on and off via its HDMI connection using CEC (Consumer Electronics Control) commands, or via the built-in IR or RS-232 port. For advanced applications using a Crestron control system, all of the HDMI, IR, and RS-232 ports on the HD-MD-200-C-E can be utilized to attain fully-programmable control of the display, sources, and other devices in the room.

Control System Integration
Fully programmable functionality can be enabled through integration with a Crestron control system. Integration with a control system also enables centralized monitoring using the Crestron Fusion® Enterprise Management Service.

Low-Profile Installation
The transmitter and receiver components (models HD-TX-101-C-E and HD-RX-201-C-E respectively) are each designed to be mounted to a flat surface or placed on a shelf. Each component is compact enough to fit discreetly inside a presentation lectern, beneath a table, on a wall behind a flat-panel display, or on the ceiling above a projector. They can even be attached to a single rack rail in the back of an equipment cabinet. Both components are powered together using a single wall mount power pack (included), which may be connected either at the receiver or at the transmitter location. Power is carried between the transmitter and receiver over the DM Lite link connection.

Easy Setup
Simplified setup, configuration, and basic operation is provided through a web browser user interface. Essential controls and status indicators are also provided on each unit for easy testing and troubleshooting without a computer during installation.

Video
Switcher	1+1 (1 input at transmitter + 1 input at receiver) manual or auto-switching, audio-follow-video, Crestron QuickSwitch HD technology
Scaler	HD video scaler and deinterlacer, noise reduction, 3:2/2:2 pull-down detection and recovery, aspect ratio selection, picture and RGB color adjustments
Input Signal Types	HDMI w/Deep Color (DVI & Dual-Mode DisplayPort compatible [2])
Output Signal Types	HDMI w/Deep Color (DVI compatible [3])
Copy Protection	HDCP 1.4
Maximum Input Resolutions Input Type Scan Type Resolution Frame Rate HDMI Progressive 1920x1200 WUXGA 60 Hz 1920x1080 HD 1080p 60 Hz Interlaced 1920x1080 HD 1080i 30 Hz NOTE: Common resolutions are shown; other custom resolutions are supported at pixel clock rates up to 165 MHz
Scaler Output Resolutions, HDMI, Progressive	Auto, 640x480@60Hz, 720x480@60Hz (480p), 720x576@50Hz (576p), 800x600@60Hz, 840x480@60Hz, 1024x768@60Hz, 1280x720@50/60Hz (720p50/60), 1280x768@60Hz [9], 1280x800@60Hz [9], 1280x960@60Hz, 1280x1024@60Hz, 1360x768@60Hz, 1366x768@60Hz [9], 1400x1050@60Hz [9], 1440x900@60Hz [9], 1600x900@60Hz [10], 1600x1200@60Hz, 1680x1050@60Hz [9], 1920x1080@30/50/60Hz (1080p30/50/60), 1920x1200@60Hz [10]
Scaler Output Resolutions, HDMI, Interlaced	Auto, 480i, 576i, 1080i25, 1080i30
Audio
Input Signal Types	HDMI (Dual-Mode DisplayPort compatible [2])
Output Signal Types	HDMI, analog stereo [3]
Digital Formats	Dolby Digital, Dolby Digital EX, DTS, DTS ES, DTS 96/24, LPCM up to 8 channels
Analog Formats	Stereo 2-channel [4]
Digital-To-Analog Conversion	24-bit 48 kHz
Analog Output Volume	-80 to +20 dB Level adjustment range, plus Mute
Analog Output Lip-Sync Delay	0 to 150 ms (maximum delay time is reduced for input signals with sampling rates over 48 kHz)
Analog Performance	Frequency Response: 20 Hz to 20 kHz ±0.5 dB; S/N Ratio: >93 dB, 20 Hz to 20 kHz A-weighted; THD+N: <0.005% @ 1 kHz; Stereo Separation: >80 dB
Communications
Ethernet	10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP, web browser setup and control, Crestron control system integration
RS-232	2-way device control and monitoring up to 115.2k baud with hardware and software handshaking
IR	1-way device control via infrared up to 60 kHz
HDMI	HDCP 1.4, EDID, CEC
DM Lite Link	Proprietary link for connection between TX & RX only
NOTE: Supports management of HDCP and EDID; supports management of CEC between the connected HDMI devices and a control system
Connectors at Transmitter (HD-TX-101-C-E)
24VDC 1.25A	(1) 2.1 x 5.5 mm DC power connector; 24 Volt DC power input; PW-2412WU power pack included [8]
TO RX	(1) 8-pin RJ45 connector, female, shielded; Link port for connection to HD-RX-201-C-E receiver [1]
HDMI IN	(1) HDMI Type A connector, female; HDMI digital video/audio input (DVI and Dual-Mode DisplayPort compatible [2])
POWER ONLY	(1) USB Type A connector, female; USB power port (500 mA maximum output); Supplies power for a Crestron Multihead HD Video Cable (CBL-MULTI-HD-6, sold separately) or other USB powered device
Connectors at Receiver (HD-RX-201-C-E)
HDMI, INPUT 1	(1) HDMI Type A connector, female; HDMI digital video/audio input (DVI & Dual-Mode DisplayPort compatible [2])
FROM TX, INPUT 2	(1) 8-pin RJ45 connector, female, shielded; Link port for connection to HD-TX-101-C-E transmitter [1]; Maximum cable length: 230 ft (70 m)
HDMI OUTPUT	(1) HDMI Type A connector, female; HDMI digital video/audio output (DVI compatible [3])
AUDIO L/R	(1) 5-pin 3.5 mm detachable terminal block; Balanced/unbalanced stereo line-level audio output [4]; Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced; Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced
IR	(1) 2-pin 3.5 mm detachable terminal block; IR output control port; Supports IR up to 60 kHz; IRP2 emitter sold separately; Note: Provides power on/off control of the display device without a control system, or fully programmable control of any device with a control system
COM	(1) 5-pin 3.5 mm detachable terminal block; Bidirectional RS-232 port; Supports RS-232 up to 115.2k baud with hardware and software handshaking; Note: Provides power on/off control of the display device without a control system, or fully programmable control of any device with a control system
LAN	(1) 8-pin RJ45 connector, female; 10Base-T/100Base-TX Ethernet port
24VDC 1.25A	(1) 2.1 x 5.5 mm DC power connector; 24 Volt DC power input; PW-2412WU power pack included [8]
SERVICE	(1) USB Type A connector, female; For factory use only
Indicators at Transmitter (HD-TX-101-C-E)
PWR	(1) Green LED, indicates operating power is supplied from the power pack via the 24VDC input or from the RX via the DM Lite link
HDMI IN	(1) Green LED, indicates HDMI input signal presence
LINK	(1) Green LED, indicates the DM Lite link status
TO RX	(2) LEDs (on RJ45 connector), green LED indicates DM Lite link status, amber LED indicates a valid video signal
Controls & Indicators at Receiver (HD-RX-201-C-E)
FROM TX, INPUT 2	(2) LEDs (on RJ45 connector), green LED indicates DM Lite link status, amber LED indicates a valid video signal
LAN	(2) LEDs (on RJ45 connector), green LED indicates Ethernet link status, amber LED indicates Ethernet activity
PWR	(1) Bi-color green/amber LED, indicates operating power is supplied from the power pack via the 24VDC input or from the TX via the DM Lite link, turns amber while booting and green when operating
AUTO	(1) Pushbutton to enable/disable auto-switching mode, and (1) green LED to indicate auto-switching mode is enabled
INPUT 1 – 2	(2) Pushbuttons for manual input selection, and (2) bi-color green/amber LEDs to indicate the current active input and signal presence at each corresponding input
SETUP	(1) Red LED and (1) recessed pushbutton for Ethernet setup
Power
Power Pack (included)	Input: 0.8 Amps (maximum) @ 100-240 Volts AC, 50/60 Hz; Output: 1.25 Amps @ 24 Volts DC; Model: PW-2412WU NOTE: The transmitter and receiver are powered together using a single power pack. The power pack may connect to either the transmitter or receiver, not both.
Environmental
Temperature	32° to 104° F (0° to 40° C)
Humidity	20% to 90% RH (non-condensing)
Construction
Applicable to both the transmitter and receiver:
Chassis	Metal, black finish, with (2) integral mounting flanges, vented sides
Mounting	Freestanding, surface mount, or attach to a single rack rail
Dimensions
Transmitter (HD-TX-101-C-E)	Height: 1.26 in (32 mm); Width: 4.21 in (107 mm); Depth: 4.05 in (103 mm)
Receiver (HD-RX-201-C-E)	Height: 1.11 in (28 mm); Width: 7.70 in (196 mm); Depth: 4.94 in (126 mm)
Weight
Transmitter (HD-TX-101-C-E)	9.92 oz (281 g)
Receiver (HD-RX-201-C-E)	20.82 oz (590 g)
Compliance
UL Listed for US & Canada, CE, IC, FCC Part 15 Class B digital device