Crestron HZ-SWEX-A

Horizon™ In-Wall Switch with infiNET EX® Wireless Communication, 120 VAC, White

The HZ‑SWEX is a Horizon™ in‑wall switch that controls incandescent, magnetic low voltage, and tungsten‑halogen loads as well as electronic ballasts and 1/2 HP motors. Its design matches the entire line of Horizon dimmers, switches, and keypads, making it a great addition to new or retrofit installations.

Load Requirements

Load Type Incandescent, Magnetic Low Voltage, Tungsten-Halogen, Electronic Ballasts, 1/2 HP Motors

Load Rating 10 A maximum;

No minimum load

Power Requirements

120 VAC, 50/60 Hz;

Requires neutral wire connection

Controls

Pushbutton (1) large rocker button (HZ‑BTN‑RKR5‑BLANK) preinstalled;

Configurable with combinations of HZ‑BTN‑RKR1, HZ‑BTN‑RKR3, or HZ‑BTN‑1 in blank or engraved models1

Setup (1) Hidden pushbutton (behind faceplate's top trim piece);

Configures the LED backlight and calibrates the light sensor

LED Indicator and Light Sensor

Feedback (5) Color‑adjustable LEDs;

Provides button backlighting

Light Sensor

Photosensor with adjustable sensitivity;

Detects the ambient light level to activate day or night mode

NOTE: Light sensor performance may be affected by obstructions placed below the keypad.

Wireless

RF Transceiver infiNET EX® 2‑way RF, 2.4 GHz ISM Channels 11‑26 (2400 to 2483.5 MHz), default channel 15;

IEEE 802.15.4 compliant

Range (typical) 150 ft (46 m) indoor, 250 ft (76 m) outdoor to nearest mesh network device(s);

Subject to site-specific conditions and individual device capabilities2

Gateway Requires an infiNET EX gateway1

Connections

Load (1) 14‑12 AWG, screw terminal, red, load output

Line (1) 14‑12 AWG, screw terminal, brass, line power input

Neutral (1) 14‑12 AWG, screw terminal, silver, neutral

Remote (1) 14‑12 AWG, screw terminal, blue, remote

Ground (1) 14‑12 AWG Class 1 flying lead, green, ground (wire nut included)

Environmental

Temperature 32° to 86° F (0° to 30° C)

Humidity 10% to 90% RH (noncondensing)

Enclosure

Mounting Mounts in a 1‑gang U.S. electrical box or plaster ring (not included);

3.5 in. (26 mm) electrical box depth recommended;

Gangable up to four units

Faceplate Requires an HZ‑FP‑G Horizon faceplate (not included)

Dimensions

Height 4.13 in. (112 mm)

Width 1.80 in. (46 mm)

Depth 1.75 in. (45 mm) overall, extends 0.41 in. (11 mm) from wall surface when installed

Weight

6.7 oz (190 g)

The HZ‑SWEX is a Horizon™ in‑wall switch that controls incandescent, magnetic low voltage, and tungsten‑halogen loads as well as electronic ballasts and 1/2 HP motors. Its design matches the entire line of Horizon dimmers, switches, and keypads, making it a great addition to new or retrofit installations.

Integrated Keypad

Supporting up to five buttons, the HZ‑SWEX is configurable for a variety of applications. Because the switch is attached to the Crestron® network, it can function as a keypad to trigger remote actions.

Multiway Control

The HZ‑SWEX supports load control from multiple locations. Up to four HZ‑KPEX or HZ‑AUX devices1 can be connected to a traveler wire in a traditional three- or four-way circuit to switch the load attached to the HZ‑SWEX. The HZ‑KPEX provides backlit, engravable button caps for multiway control, while the HZ-AUX provides a single large rocker button.

Multigang Expansion

Up to four devices may be installed side‑by‑side in a multigang electrical box with a compatible Horizon faceplate (HZ‑FP‑G series).1 All buttons in a multigang arrangement align to form one continuous control surface.

infiNET EX Communications

infiNET EX wireless technology provides two‑way RF communications throughout a residential or commercial structure without the need for physical control wiring. Each infiNET EX device acts as an expander by sending command signals to other infiNET EX devices in range (approximately 150 ft (46 m) indoors) to ensure reliability and stability.2

The HZ‑SWEX communicates with a control system via a CEN‑GWEXER1 or newer infiNET EX Wireless Gateway. Up to 100 infiNET EX devices may coexist on a wireless network.

Field-Replaceable Button Caps

The preinstalled rocker button cap on the HZ‑SWEX is field replaceable, allowing for engravable multi‑button configurations.

Multicolor Backlit Button Engraving

Horizon button caps are laser engravable to identify each button's function. RGB LED backlights illuminate the engraved labels and can be adjusted for custom color backlighting. A built‑in ambient light sensor enables auto‑dimming of the backlight brightness according to day and night mode presets.

Each button's backlight provides feedback by changing color, intensity, or both. The backlight can also flash to show that an action is being performed.

Customizable Faceplates

Horizon compatible faceplates are customizable for any décor. Color‑matched top and bottom trim pieces may be swapped easily after installation with custom trim fabricated from solid materials such as wood, metal, marble, engineered stone, or Corian®. Contact a Crestron representative, or refer to Crestron True Blue Support Online Help Answer ID: 1000140, to obtain specifications and CADs for the fabrication of custom trim. Paintable trim is also available separately.

Note: The faceplate trim is attached magnetically, which may inhibit use in locations where tampering may occur.

Key Features

Supports multiway controllers (HZ‑AUX, HZ‑KPEX)

Single‑gang U.S. wall box installation

Requires neutral wire connection

Gangable up to four across using Crestron® Horizon™ device compatible multi‑gang faceplates (HZ‑FP‑G series)

Robust infiNET EX® wireless communication

Preinstalled large rocker button

Configurable with up to five field‑replaceable buttons

Custom backlit laser‑etched engravable buttons

Multicolor RGB LED backlighting

Auto‑dimming day/night backlight modes

Local button for load control without programming

Fully programmable via a Crestron control system

Crestron Home™ OS 3 compatible