Environment Controls

The C2N-MNETGW is a 2-way RF gateway/transceiver designed to enable communications and management for a complete infiNET wireless network of dimmers, keypads, and other devices. The C2N-MNETGW links the infiNET network to a Crestron control system via Cresnet.

The C2N-SDC is a 2-channel Shade and Drape Controller designed to provide a convenient and cost-effective solution for controlling a variety of motorized window treatments as well as motorized doors, sunroofs, lifts and projection screens. The C2N-SDC is a Cresnet device with two independently controlled 120V AC outputs. Each output provides up/down or open/close control of a conventional three-wire bidirectional type motor. Built-in timing and interlock logic make it easy to program the...

The C2N-SDC-DC is a 2-channel Shade and Drape Controller designed to provide a convenient and cost-effective solution for controlling 24 Volt DC motorized shades and drapes. The C2N-SDC-DC is a Cresnet device with two independently controlled 24V DC outputs, each designed to provide standard up/down or open/close control of a conventional two-wire bidirectional type motor.

The C2N-SSC-2 Somfy Shade Controller is a compact Cresnet device designed to provide a bidirectional serial interface for up to two Somfy ILT[1] Intelligent Shade Motors. Window treatments equipped with the Somfy ILT motor offer enhanced capability compared to typical three-wire models.

The CAEN Series automation enclosures are designed to house Crestron's CLX-Series lighting control modules and PAC2 or PAC2M control systems. CAEN enclosures are available in an assortment of sizes, suitable for surface or flush wall mount installation. Each model has been engineered to provide a clean and manageable installation with abundant provisions for wire termination and electrical knockouts.

The CAEN Series automation enclosures are designed to house Crestron's CLX-Series lighting control modules and PAC2 or PAC2M control systems. CAEN enclosures are available in an assortment of sizes, suitable for surface or flush wall mount installation. Each model has been engineered to provide a clean and manageable installation with abundant provisions for wire termination and electrical knockouts.

The CAEN Series automation enclosures are designed to house Crestron's CLX-Series lighting control modules and PAC2 or PAC2M control systems. CAEN enclosures are available in an assortment of sizes, suitable for surface or flush wall mount installation. Each model has been engineered to provide a clean and manageable installation with abundant provisions for wire termination and electrical knockouts.

The CAEN Series automation enclosures are designed to house Crestron's CLX-Series lighting control modules and PAC2 or PAC2M control systems. CAEN enclosures are available in an assortment of sizes, suitable for surface or flush wall mount installation. Each model has been engineered to provide a clean and manageable installation with abundant provisions for wire termination and electrical knockouts.

The CAEN Series automation enclosures are designed to house Crestron's CLX-Series lighting control modules and PAC2 or PAC2M control systems. CAEN enclosures are available in an assortment of sizes, suitable for surface or flush wall mount installation. Each model has been engineered to provide a clean and manageable installation with abundant provisions for wire termination and electrical knockouts.

The CAEN-BLOCK is a Cresnet terminal block designed specifically for Crestron lighting and automation systems to link extension enclosures and satellite enclosures to the central PAC2 or PAC2M control system. The CAEN-BLOCK mounts at the bottom of each CAEN or CAENIB enclosure that does not contain a control system to provide Cresnet and Override signal connectivity for CLX-Series lighting control modules within. The CAEN-BLOCK serves as a parallel distribution block for multiple Cresnet...

Ethernet to Cresnet Bridge for CAEN Automation Enclosures

CAEN-CK Cover Kits are designed to extend the depth of Crestron's CAEN and CAENIB Automation Enclosures, affording 1.5 inch (3.81 cm) additional depth to accommodate EX ess wiring and third-party devices.

CAEN-CK Cover Kits are designed to extend the depth of Crestron's CAEN and CAENIB Automation Enclosures, affording 1.5 inch (3.81 cm) additional depth to accommodate EX ess wiring and third-party devices.

CAEN-CK Cover Kits are designed to extend the depth of Crestron's CAEN and CAENIB Automation Enclosures, affording 1.5 inch (3.81 cm) additional depth to accommodate EX ess wiring and third-party devices.

CAEN-CK Cover Kits are designed to extend the depth of Crestron's CAEN and CAENIB Automation Enclosures, affording 1.5 inch (3.81 cm) additional depth to accommodate EX ess wiring and third-party devices.

CAEN-CK Cover Kits are designed to extend the depth of Crestron's CAEN and CAENIB Automation Enclosures, affording 1.5 inch (3.81 cm) additional depth to accommodate EX ess wiring and third-party devices.

The CAEN-MK is the mounting kit required to mount (1) C2N-SPWS300 Cresnet power supply or (1) C2N-NPA8 Cresnet network poll accelerator into a CAEN or CAENIB automation enclosure. Using the CAEN-MK, either component occupies 1 module space in a single-width CAEN enclosure, or 2 side-by-side module spaces in a double-width CAEN enclosure. The complete kit includes all DIN rail terminal block components required to terminate the device's 120VAC power cable.

CAEN-CK Cover Kits are designed to extend the depth of Crestron's CAEN and CAENIB Automation Enclosures, affording 1.5 inch (3.81 cm) additional depth to accommodate EX ess wiring and third-party devices.

CAEN-CK Cover Kits are designed to extend the depth of Crestron's CAEN and CAENIB Automation Enclosures, affording 1.5 inch (3.81 cm) additional depth to accommodate EX ess wiring and third-party devices.

The CAENIB Series automation enclosures are designed to house Crestron's CLXI-Series lighting control modules with optional load-side circuit breakers, and a PAC2 or PAC2M control system. CAENIB enclosures are available in an assortment of sizes, suitable for surface or flush wall mount installation. Each model has been engineered to provide a clean and manageable installation with abundant provisions for wire termination and electrical knockouts.

The CAENIB Series automation enclosures are designed to house Crestron's CLXI-Series lighting control modules with optional load-side circuit breakers, and a PAC2 or PAC2M control system. CAENIB enclosures are available in an assortment of sizes, suitable for surface or flush wall mount installation. Each model has been engineered to provide a clean and manageable installation with abundant provisions for wire termination and electrical knockouts.

The CAENIB Series automation enclosures are designed to house Crestron's CLXI-Series lighting control modules with optional load-side circuit breakers, and a PAC2 or PAC2M control system. CAENIB enclosures are available in an assortment of sizes, suitable for surface or flush wall mount installation. Each model has been engineered to provide a clean and manageable installation with abundant provisions for wire termination and electrical knockouts.

Designed for the CAENIB Series Automation Enclosures, these blank plates are used to fill the holes in the enclosure cover panel in front of any terminal block position that does not have a CLTIBN type circuit breaker terminal block installed. A set quantity of blank plates is included with each enclosure. The CAENIB-BP provides 5 additional blank plates and hardware.

The CH-RTHS-N is a wall mount temperature and relative humidity sensor. It mounts in a single‑gang UK or EU style electrical box and communicates directly with any Crestron® Control System via the Cresnet® control network. A complete installation requires an FP-INTENSE FP-PURE series faceplate (sold separately).